Recoup Energy Solutions: What is a Waste Water Heat Recovery System?

Waste Water Heat Recovery (WWHRS) is a system or technology that uses the residual heat from waste shower water to preheat the incoming cold feed that refills the system.

Therefore, less energy is required to heat that water to the required temperature. WWHRS saves energy, what would be wasted heat energy going down the drain is recovered and reused.


As properties become more efficient preventing energy loss in fabric and heating, hot water energy will become the largest source of wasted energy in a property.

How WWHRS Works

The main requirement for WWHRS is the incorporation of a Thermostatic Mixing Valve (TMV) on the shower mixer. As the cold mains water starts to preheat from the WWHRS heat exchange the TMV will automatically reduce the showers demand of hot water from the properties water heater. If preheated water is also being sent to the water heater, then less energy is also required to heat the preheated water to the required temperature.

Waste Water Heat Recovery (WWHRS) can be used alongside any method for heating shower water.

  • Combi Boiler (All fuel types)
  • Hot Water Cylinder
  • Thermal Store
  • Heat Interface Unit (HIU)
  • Heat Pumps

As showers will always require a hot water source, WWHRS can always be incorporated to save energy by sending pre-heated water directly back to the cold side of the shower. Some heating types and some property configurations may not allow the preheated water to be sent back to the water heater as well.

Installation methods

There are three installation methods to choose from, each having an effect on the WWHRS performance and efficiency.

● System A, the most efficient, preheated water is supplied to the water heater and the shower.

● System B provides preheated water to just the shower. Lower WWHRS efficiencies produced than System A or C, but it is the easiest method to install or retrofit.

● System C provides preheated water to just the water heater. Greater WWHRS efficiencies than System B are produced but lower than with System A. This installation method is often used when two showers are running into one WWHRS.

Benefits of WWHRS

  • Horizontal and vertical options catering for all application types and locations
  • High-efficiency units recovering a large proportion of wasted shower energy

  • Easy to install

  • Cost-effective solution, ROI typically within one to four years of use

  • Virtually maintenance-free

  • No end-user interaction is required

  • Double-walled heat exchangers

  • KIWA validated efficiencies of up to 68.5%

  • WRAS approved

  • Legionella control risk assessed

  • SAP listed on the Product Characteristics Database (PCDB)

Product types

There are horizontal and vertical WWHRS product types. The suitable application of a horizontal or vertical product is determined by the building type, the location of the shower within the building and the showering environment.

The Recoup Pipe HEX is an example of a vertical WWHRS product type. It is designed to install on a lower floor under the location of the shower. Therefore, it is only applicable to showers on the first floor and above. The Recoup Easyfit+, Recoup Drain+ Range, and Recoup Tray+ are examples of horizontal WWHRS product types. The Easyfit+ is specifically designed to install under a bath or raised shower tray. The Drain+ Range has wet room applications. The Tray+ incorporates the heat exchanger into a shower tray itself. Horizontal WWHRS products are typically installed on the same floor as the shower and therefore can be applied to ground floor showers as well.

Community comments

Latest News

Webinar Replay: BIM’s Role In Product Specification

Posted 27.03.2024

Introduction to BIM Webinar: BIM’s Role In Product Specification
Play VideoPlay Video

This webinar series was curated especially for an audience concerned with the Australian built environment. A range of industry pioneers revealed how BIM & Revit content is going to transform the world of construction there. It featured practical tips and real-life experience from knowledgeable experts. In this second episode, hear from Adam Ward, CTO of Space Group. This very accessible session is for people at all stages of their Building Information Modeling (BIM) journey. He will take you through BIM and its role in product specification.

Hamworthy Heating: The benefits of Stainless Steel in hot water generation

Posted 26.03.2024

With stainless steel becoming a popular choice for hot water products, our friends at Hamworthy Heating take a look at some of the key factors driving this trend.

Fire Protection Is Key for New FrameSafe FR Membrane

Posted 25.03.2024

Leading manufacturer Glidevale Protect has launched Protect FrameSafe FR - a new Class A2-s1, d0 flame retardant external wall breather membrane offering fire protection across low, medium and high-rise buildings.

CloseClose